The OBM U series is equipped with standard 12G-SDI input interface(x2) , 3G/HD-SDI input interface(x2) and support 4K Quad Link 2-Sample Interleave signals and 4K Quad Link Square Division signals. The OBM U series can accept up to 3840x2160/24,25,30,50,60p and 4096x2160/24.25.30,50,60p signals.
4K Waveform Monitor and Vector Scope Display (OBM-X/U/W Series)
These features enable users to monitor sources using the internal Waveform and Vector Scope. Waveform Wide mode* is supported, and both Waveform and Vector Scope can be displayed simultaneously. *OBM-U170 model is only supported.
High Dynamic Range(HDR) Display Function (OBM-X/U/W/P/N/H/L/Q Series)
The OBM series provides the function to display the High Dynamic Range footage. Postium HDR function allows users to view both highlights and shadow detail of scenes at tha same time, thus resulting in more natural and realistic images. The OBM series supports PQ EOTF (SMPTE ST 2084), Hybrid Log Gamma and S-Log3.
OBM-HDR provides the function of comparing HDR and SDR(Standard Dynamic Range) on the displayed image on the OBM series simultaneously.
Focus Assist (OBM-X/U/W/P/N/L/H Series)
This function controls the aperture level of a video signal, and
displays images on screen with sharpened edges to help camera focus operation.
Color Space & Gamma Comparison (Side by Side) (OBM-X/U Series)
This unique function allows users to compare the two different color spaces, gammas, color temperature, camera logs and any other color settings side by side simultaneously. The area of the two pictures to be displayed can be selected using a vertical WIPE pattern.
Various 4K/12G Display Modes
* OBM-X/U Series Support - Single Link 12G-SDI, Dual Link (2-S.I.), Quad Link(2-S.I),
Quad Link Square Division
*OBM-W Series Support - Single Link 12G-SDI, Dual Link (2-S.I.)
Fast Mode (OBM-U*/W/P/N Series)
This function minimizes the interlaced video processing time delay. This mode is also useful when displaying fast-motion interlaced video content and when reducing the delay between video and audio. * OBM-U090/U170/U171 are only supported
False Color (OBM-X/U/W/P/N/L/H Series)
This function evaluates the Luma(Y') level of the input image. If the certain Y' level is set, the pixels with the designated Luma(Y') level are displayed with the zebra pattern or the color pattern. There are three modes in OBM False Color.
Wide Color Gamut Supporting DCI-P3 and ITU-R BT.2020 (OBM-X/U Series)
The wide color gamut and the advanced 3D LUT function enable
the OBM series to reproduce various color spaces accurately and the excellent grayscale. You can select from color gamuts such as DCI-P3, ITU-R BT.2020, ITU-R BT.709, SMPTE-C, EBU, Native.
Adjustable Gamma (OBM-X/U/W/P/N/L/H/Q Series)
Gamma value is adjustable from 1.0 to 3.0 as user's preference to monitor in the dark area of the picture. Any pictures taken in either light or dark environment can be easily watched or analyzed.
Black Stretch (OBM-X/U Series)
The Black Stretch increases the visibility of subjects in dark areas, not degrading image quality in bright areas. This mode can be used to increase shadow detail without changing the absolute black level, and without affecting mid-tones.
12G-SDI over IP Supporting ST 2022-6 (OBM-X/U/W Series)
The OBM-U and OBM-W series have the SFP interface, which
allows to use the various SFP modules which can fit any possible broadcast applications. The OBM-U and OBM-W series monitors can display the 12G-SDI over fiber and the 12G-SDI Single Link over IP through the integrated SFP interface. The OBM-X310 has the dual SFP Input cages, which enable the monitor to accept and display the Quad-Link square division and 2-Sample Interleave 4K signals over IP supporting SMPTE ST 2022-6.
Camera Log Selection (OBM-X/U/W/P/N/L/H Series)
The OBM series has the built-in camera LUT of the various camera manufacturers. It allows users to load the following camera logs. Log-C, C-Log / S-Log2, S-Log3 / J-Log1 The more camera LUTs will be updated.
Camera Log Mapped SDI Loopout (OBM-X/U/W/P/N/L/H Series)
This function allows to load the camera log to the original image and then send the camera log mapped image to another monitor through SDI loop out.
Remote Control via Ethernet (OBM-X/U/W/P/N/H Series)
The OBM series can be connected via Ethernet connection and controlled remotely on the network.
Closed Caption (OBM-X/U/W/P/N/L/H Series)
The OBM series can display closed captions with an SDI input. It supports the CEA-708(HD-SDI closed captioning standard) and CEA-608(SD-SDI closed captioning standard).
Waveform & Vector Scope Position Changeable (OBM-X/U/W/P/N/L/H Series)
The position of Waveform and Vectro Scope can be changed among Left Top, Right Top, Right Bottom, Left Bottom.
The image size of Waveform and Vector Scope can be changed between Small and Large.
System Data Copy (OBM-X/U/W/P/N/L/H Series)
This function allows users to save the monitor configuration and adjustment settings on the USB memory stick and load them to other monitors. This is useful for multiple monitor systems, allowing the transfer of one monitor’s setup and adjustment data to another.
Various Markers (OBM-X/U/W/P/N/L/H/Q Series)
The OBM series can display various markers, including aspect marker, area marker, and center marker. In addition, the detailed display settings of each marker are allowed. For example, the color, brightness, horizontal/vertical position, and thickness of aspect markers can all be adjusted.
HDR / Camera Log Comparison (OBM-W/N/L/H Series)
The unique function allows users to compare HDR and Camera
Log side by side. The comparison area can be moved and selected by using the vertical Wipe pattern.
Gamut Error (OBM-X/U/W/P/N/L/H Series)
The total range of the SDI 10bit signal is 0 to 1023. The range 0 to 3 and 1020 to 1023 are the reserved values for Sync, and the total video signal range is 4 to 1019. In a video signal, each primary component should lie between 0 and 100% of the video range between black level and peak level (R and G and B). Ideally, video levels should lie within the specified limits so that programs can be distributed without adjustment.
100% White pattern: Y - 940, Cb - 512, Cr - 512 0% Black pattern: Y - 64, Cb - 512, Cr - 512 Expected Video Range: 64 to 940
In practice, it is difficult to avoid generating signals slightly out of range, and it is considered reasonable to allow a small tolerance. Therefore, the EBU recommends that the RGB components and the corresponding Luminance (Y) signal should not normally exceed the “preferred minimum/maximum” range of digital sample levels in the table above.
Type1 : Black Zebra When the targeted color space is selected as BT.709, the pixels outside of the targeted color space are displayed as Black Zebra. The pixels over Y Maximum, Chroma Maximum, RGB Maximum are displayed as Black Zebra, and the pixels below Y Minimum, Chroma Minimum, RGB Minimum are also displayed as Black Zebra.
Type 2: Black & White Zebra When the targeted color space is selected as BT.709, the pixels outside of the targeted color space are displayed as Black or White Zebra. The pixels over Y Maximum, Chroma Maximum, RGB Maximum are displayed as Black Zebra, and the pixels below Y Minimum, Chroma Minimum, RGB Minimum are displayed as White Zebra.
Type 3: Mono When the targeted color space is selected as BT.709, the pixels inside of the targeted color space are displayed as Mono, and the pixels outside of the targeted color space are displayed as the color. In this type, black and white area is not recognized.
PBP(Picture-by-Picture) (OBM-P Series)
The unique Picture-by-Picture function of the OBM P series allows two different SDI input signals to be displayed on the screen simultaneously. This function is very convenient for making instant adjustments to two input sources, because there is no need to individually adjust the different characteristics of two monitors. The OBM P series offers the various Picture-by-Picture modes as follows.
1:1 Scan in PBP Mode (OBM-P Series)
This function allows to magnify the either image of the two inputs in PBP mode.
The OBM P series can display Waveform, Vector Scope on the two different SDI videos respectively, which is very useful and convenient for dual monitoring.
WIPE (OBM-P Series)
The area of the two pictures to be displayed is selected using a vertical WIPE pattern. This function is useful when picture detail of the two images must be examined on a pixel basis.
Color Settings Adjustable to Either of Two Images in PBP Mode (OBM-P Series)
OBM PBP function allows to adjust the color settings to either of the two imanges and compare the two images. Brightness, Contrast, Color Temperature, Camera Lut, and other color settings can be changed.
This unique function allows to display the same image side by side, change the color settings to one image, and then compare the original image and the changed image on the screen.
HDR Waveform (OBM-X/U/W/P/N/L/H/Q Series)
When HDR more is set on, HDR Waveform is displayed on screen.
In-Monitor Display(IMD) Function (OBM-X/U/W/P/N/L/H/Q Series)
The image source names and tally information can be displayed on the screen, with an external remote function via Ethernet. The TSL system protocol is supported. The color of the source name and tally color can be selectable among White, Red, Green, Blue, Yellow, Cyan, Magenta.
Password Lock for User Preset (OBM-X/U/W/P/N/L/H Series)
When multiple users share the same monitor, each user can register his/her own password for color temperature and user preset data. This ensures the users correctly recalls their preset data, and keeps preset information safe from unauthorized use.
Custom 3D LUT File Import (OBM-X/U/W/P/N/L/H Series)
The OBM series allow the user to import 3D Look-up Table for accurate and consistent color matching between indivisual displays. as well as using customized ‘looks’ that have been createcl by 3rd party color-grading applications. 33ˆ³ and 65ˆ³ cube file is supported.
Scan Mode (OBM-U/W Series)
When the 4096 x 2160(1.89:1) signal is fed to the 1920x1080(16:9) resolution sceen, if you select Zero Scan mode, the whole picture is displayed on the screen, with maintaining 1.89:1 ratio.
Focus Assist (OBM-X/U/W/P/N/L/H Series)
This function controls the aperture level of a video signal, and displays images on screen with sharpened edges to help camera focus operation.